How To Tighten Toilet Seat With No Access Underside

• How To's & Quick Tips

How To: Tighten a Toilet Seat

Follow this guide to control a example of the wobbles.

Photo: istockphoto.com

From the force per unit area of people sitting to the abiding opening and closing of the lid and/or seat, your toilets probably get more traffic than any other seat in the house. And then it'due south understandable that the seat could loosen and wiggle a flake from side to side. The bolts that attach the seat to the commode, located but behind where you sit, are causing the problem. This is no mere annoyance but a potentially unsafe situation, should the hat separate from one of its bolts while someone's using information technology, causing injury. Fortunately, the fix is bound to be an easy DIY job—whether you simply need to arrange the bolts or replace them entirely. Read on for two ways to go about how to tighten a toilet seat.

Program A: Tighten the Bolts

TOOLS AND MATERIALS Available on Amazon
– Flathead screwdriver
– Toilet seat hinge washers (optional)
– Ratchet wrench
– Adjustable wrench (optional)

Stride 1

Locate the two bolts that attach the seat to the commode. If in that location are small plastic cases covering the bolts, use your fingers to pop them open the same way you might access a shampoo cap; many modern toilet seat commodities covers are manufactured with this feature. If not, use a flat caput screwdriver to gently pry them loose and expose the bolts.

Footstep 2

Use the screwdriver to tighten the toilet seat bolts, which are now exposed, screwing clockwise until they resist. Exist sure to stop when each bolt stops turning; yous don't want to strip or break them altogether. Alternatively, consider adding a toilet seat swivel washer (less than $ane apiece) to each commodities. These washers were designed for the specific purpose of keeping a toilet seat in identify. If yous choose to do so, proceed to the next stride.

STEP 3

To install the seat hinge, unscrew the bolts entirely using a counterclockwise motion with your screwdriver. Slip the washers into place where the bolt volition meet the commode before reinserting the bolts and screwing them back.

STEP 4

If bolts fail to tighten, try holding the nut at the base of the bolt in place with a pair of pliers in i hand while turning the bolt clockwise with the screwdriver in the other mitt. In one case again, take care not to go also far and damage the bolt or strip information technology; once it stops turning, y'all're done.

Photo: istockphoto.com

Programme B: Replace the Bolts

TOOLS AND MATERIALS Bachelor on Amazon
– Miniature hacksaw
– Toilet seat replacement kit
– Replacement nuts and bolts with prophylactic washers (optional)

STEP 1

If the bolts are frozen in place and only won't budge, cut them off with a miniature hacksaw. Identify the saw blade just beneath the commodities'southward head and saw slowly until y'all've gone all the way through the metallic.

Stride 2

After sawing through the commodities, the severed piece may exist hot to the impact, then use caution when removing information technology. Repeat the process on the other commodities, then articulate abroad whatsoever debris on both sides. Remove each nut by spinning it counterclockwise, then pull the bolts out and discard them.

Pace 3

If y'all need to replace hinges likewise as the bolts, it'due south best to purchase a toilet seat replacement kit for less than $10 at your local hardware store. This includes nuts, bolts, and hinges with screws. Otherwise, you only demand replacement nuts and bolts with safety washers.

Then, with onetime or new hinges securely in place, screw the bolts in one at a time by holding each nut at the base, dropping the bolt into the center of the nut, and using your screwdriver to secure each bolt in a clockwise motion. This should do the trick to tighten the toilet seat. Test the seat to make sure it doesn't move side to side, and you should be sitting pretty!

Source: https://www.bobvila.com/articles/how-to-tighten-a-toilet-seat/

Share this post